Digitrax SCF8A Super Chief Radio 8-Amp DCC System LNIB

Description

Here we have a
Digitrax SCF8A Super Chief Radio 8-Amp DCC System LNIB
Like-new in the box. Complete with manual. Very light use.
NOTE: Power supply sold separately.
The Super Chief 8 Amp starter set contained a DCS200 command station, a DT400 throttle, a UP5 Universal Panel, and a LT1 LocoNet tester.
In addition the Super Chief 8 Amp starter set was available as a Radio Equipped Set.
The photo is of a 5 amp Super Chief.  The 5 amp set contains a DCS100 as shown.  The 8 amp set contains a DCS200 command station which is similar in appearance to the DCS100.
DCS200 Command Station / Booster:
Full LocoNet Capabilities for easy plug 'n play installation and system expansion
Run up to 120 locos and 120 throttles in command station mode.
Provides additional power to run more trains in booster mode.
Can be used as an Intelligent Auto Reversing Booster
Use with any LocoNet throttle
Read/Write programming with CV readback
Two DCC outputs so you can run your trains and program at the same time.
Built in 8 Amp Digital Command Control Booster to give you maximum power
Many command station options are user customizable.
Auto resetting over temperature & short circuit protection.
User selectable multi-scale operation for N, HO, and large-scale layouts
Track Status indicator shows voltage and signal type (DCC or "Zero Stretch" Analog Signal for conventional operation.)
Stabilized Track Drive Output.
Over Voltage Protected.
Auto shutdown if command control drive signal is lost so that the layout will not convert to DC operation if a cable or connection is broken. The trains won't just "take-off" if they are not getting the DCC signal.
Complies with FCC Part 15, Class B RFI Requirements.
DCC Compatible.
DT400 Features:
Simple to use with any Digitrax LocoNet System
User Friendly Multi-line backlit display with easy to read icons and messages
Dual throttle controls for running two trains at a time
Click encoders give extra fine speed control and direction control, too!
Full numeric keypad
Direct access to functions 0-12 with DCS50 or DCS100 command stations
Direct access to functions 0-8 with DB150 command station
Single key access to most common throttle tasks.
Infra-Ready
Find Key for use with transponder equipped locos & layouts
Built in flashlight for reading paperwork and loco/car numbers in darkened layout rooms
No more throttle display time-outs!
UP5 Features:
Plug 'N Play Instalation
Gives your layout a professionally finished look.
Two RJ12 6 pin LocoNet jacks in the back of the panel for hooking up LocoNet devices that use RailSync.
Two RJ12 6 pin Throttle jacks in the front of the panel for hooking up throttles and other LocoNet devices that do not use RailSync.
One additional RJ12 6 pin Throttle jack on the side of the panel for hooking up LocoNet devices that do not use RailSync.
Indicator LED that shows the power state of a local track section.
2mm power jack that allows you to make the UP5 a battery saver terminal for your throttles by plugging in a PS14 DC power supply.
Two #6-32 right angle screw terminals for local track connections for power and diagnostics.
Please look at the pictures to see exactly what you will receive.
MUST USE SHOPPING CART FOR COMBINED SHIPPING RATES!
California buyers pay sales tax.
Shipping outside of the USA is Global Shipping Program only.
Milepost 38 Toy Trains / Arnie's Model Trains is the largest train center on the West Coast!
Located in Orange County, CA. Open 6 Days a week!
WE BUY TRAINS!
Delayed shipping is not allowed after payment
If you need to delay shipping contact us before payment otherwise the item will be shipped immediately.